STANDARD JAMB DEPTHS
S-Series: 3 3/4″, 4 5/8″, 4 7/8″, 5″ and 5 3/8″
C-Series (18 gauge): 3 1/2″, 3 3/4″, 4″, 4 5/8″, 4 7/8″, 5″, 5 3/8″, 6 5/8″, 6 7/8″ and 7 1/4″
CUSTOM JAMB DEPTHS
C-Series (18 gauge): 2 5/8″ to 13″ in 1/8″ increments.
Note: The available jamb depths and door weights listed here apply to the Classic Frame in general. Some limitations may apply when looking at specific information. For example, a communicating frame must have a larger minimum jamb depth than listed here.
| | | |
|---|
| FRAME MATERIALS | JAMB – NO STOP | | JAMB – WITH STOP |
| Prefinished Steel | 1U Custom Jamb Depths C-Series (18 gauge): 2 5/8" to 13" in 1/8" increments. | | 1Y Standard Jamb Depths:
S-Series (20 gauge)**: 3 3/4", 4 5/8", 4 7/8", 5" and 5 3/8"
C-Series (18 gauge):
3 1/2", 3 3/4", 4", 4 5/8", 4 7/8", 5", 5 3/8", 6 5/8", 6 7/8" and 7 1/4"
Custom Jamb Depth:
1Y C-Series (18 gauge): 2 5/8" to 13" in 1/8" increments. |
| JAMB DEPTHS | | | |
| CUSTOM | STANDARD | |
| Max. Opening Width: | 9' 8" | 12' 0" | |
| Max. Opening Height: | 10' 1" | 12' 0" | |
| All widths and heights are inside dimensions – net door or glass opening size. | | | |
ROUGH OPENING DIMENSIONS
WIDTH 
Rough opening width is 1 1/4″ over nominal door width. This provides for 5/8″ clearance between the jamb and the wall. This clearance is necessary for the pocket on the strike and the projection of the hinge screws. Frames can be installed with smaller opening widths but, in some cases, the framing must be relieved to provide the necessary clearance for plumbing the frame and installing the hardware. Opening width maximum is 1 7/8″ which allows 5/16″ of the frame face against the wall. For wider rough openings, the frame must be positioned with equal clearance on both sides. (Use oval alignment slots to adjust clearance when installing)
ROUGH OPENING WIDTH: Classic Frames (S-Series and C-Series) –
Nominal door width + 1 1/4″
HEIGHT
Rough Opening height must provide clearance to level the header and interlock the jambs. Uneven floors will affect this measurement. Maximum space for adequate anchorage is 1 3/16″ over net height resulting in approximately 5/16″ of the frame face against the wall. While this is not recommended, the frame can still be installed.
Timely standard height – 3/16″ over nominal.
ROUGH OPENING HEIGHT: Nominal Height + 1″ (Net height +13/16″)
Net Height – Frames manufactured to net heights
ROUGH OPENING HEIGHT: Net height + 13/16″
Please select “Products > Casing Options” from the main menu if you require additional information regarding Timely’s casing options.
Wood casing: can easily be applied to Timely frames. This requires a frame without Casing Retainer Clips. Specify frames with nail holes and oval slots (NHOS) only Wood casing is then installed over the frame face using a nail gun or trim head screws. Casing profile must provide back clearance for screw heads used to install frame.
Fire Ratings: Wood casing must be applied with hot melt glue or contact adhesive on 90 minute rated frames and on all glazed openings with 45 minute or 60 minute rating. On all other fire rated frames, wood casing can be applied with nails or finish head screws on jambs and mullions.
STANDARD FINISHES
PRE-MATCHED CUSTOM FINISHES
ELITE SERIES
430 BRIGHT STAINLESS STEEL (ES204)
304 #4 BRUSHED STAINLESS STEEL (ES206)
Custom color matching is also available. Submit color chip for matching. Consult factory for pricing and lead times.
Notes: Color chips available upon request, all finishes are semi-gloss unless otherwise specified. Touch-up paint available upon request, colors may vary slightly. For complete technical information, contact your Timely distributor or our Marketing Service Department. Colors & price subject to change.
